GOLEMArchitecture·Art·Design

08.e.1How can shelving divide a room while keeping both sides usable?

A low, double-sided shelf can give a reading area an edge and keep the entrance in view, with the rest of the collection on the walls or deeper in the room. To compare layouts with the same number of books, the designer can draw someone browsing while a cart passes on one side and show a pulled-out chair on the other. The space those activities take sets the depth available for the shelf.

Put the same collection into more than one plan

The Massachusetts Board of Library Commissioners’ planning guide compares arrangements that store similar lengths of books in low, mid-height, and tall shelving. The guide illustrates 360 linear feet of shelving in twelve five-high, double-sided, three-foot bays occupying about 370 square feet. Its ten-bay, six-high example stores the same length in about 320 square feet. The 50-square-foot difference belongs to those drawings. It has a practical counterpart in the taller layout, where the authors point out that “sightlines are only possible between the shelving.” Establish where any space gained would fall on your plan. An allowance that enlarges the reading area has a different value from the same area scattered across the ends of two rows. It also calls attention to the orientation of the ranges. That matters when a member of staff at a fixed desk must see whether a person has reached the end of a row or needs help. Massachusetts Board of Library Commissioners and Sasaki, Library Space

Count linear feet from the actual shelf schedule, including bins and face-out display wherever they replace spines. In one design exercise, put a strip of low shelving between a parent’s seat and a children’s collection and place the taller capacity on a wall. In another, turn the divider ninety degrees and compare the paths from the entrance to both sides. Plot the distance staff travel with returns. The choice becomes clearer when the same amount of shelving is on both drawings and the floor area includes the places where people stop.

The French Ministry of Culture’s illustrated technical note uses furniture to identify different functions inside a one-room library and calls for visibility from reception. It illustrates the idea in its recommendations for low double-sided shelving projecting into the room in short runs. A Brazilian federal reference design for a small library recommends against high shelving in the center and puts the main collection against a wall opposite the main window. It also includes forward-facing books. The Brazilian drawing is a reference design rather than a record of occupied performance. It gives the designer a practical layout to test when a small room has to accommodate browsing and reading in the same line of sight. Ministère de la Culture, Fiche technique 4, Les bibliothèques et médiathèques Ministério das Cidades and Ministério da Cultura, cartilha de bibliotecas, 2025

Draw what happens at the last bay

Once a range is long enough to define a room, its ends matter as much as its height. Draw the side that receives a turning person, a return cart, or a queue to the desk. On the opposite side, draw a reader with a book open and a person approaching from the other direction. The Irish Centre for Excellence in Universal Design illustrates more than one shelf arrangement in its building-types guidance. Measure clearance to the nearest projecting component, including a wall, end panel, or display arm. The guidance shows 1,400 millimeters among its example clearances. Apply the project’s own requirements and use the illustrated layouts to test the approach and turn at each end. In section, check visibility from a seated staff position and from a child’s height. The same shelf may leave one line open and close another. Centre for Excellence in Universal Design, Building for Everyone, Booklet 7

A double-sided unit can also be asymmetrical in use. One face might carry books returned throughout the day while the back gives seated readers a shallow display they can browse without crossing the reshelving route. Show the maximum projection of an angled display tray or end panel in the dimensioned plan. A sign above the end can point across the room. A signboard or projecting tray at the same location consumes the strip where people change direction. Ask the fabricator to draw each side with the shelves loaded and the end fittings attached.

Review the shelf heights and the actual load with the supplier and whoever specifies restraint or anchorage. Dimension the top of the lowest usable shelf above the finished floor. At the review, give staff a cart and ask them to complete one reshelving round through the proposed layout. A return point that forces staff to reverse down a long dead end is a reason to split the range or reopen its far end. Record the revised shelf capacity in the schedule while the reader’s route is still easy to change.