A communal dining table needs space for the occupied seating, usable dining positions at the top and a route around it. Calculate each separately. An empty aisle dimension says little about the space when guests pull their chairs out, when a person approaches in a wheelchair or when a server passes with a hot platter. Start with the applicable local accessibility standard, then add the room the menu and service actually use.
Measure across the occupied section
A section across one long side of the table can show the space taken up by an occupied seat and the route behind it. Draw the overhang, a chair with a person sitting in it and the clearance beside or behind that chair. Use the actual chair, because its back and feet may project differently as people sit and stand. Mark the position of someone transferring, if the arrangement permits transfer. The clear circulation route has to continue past adjoining chairs and columns. At the ends of the table, put in the turns that people make when they arrive, then check whether the position of a trestle or a long low rail removes knee or foot space. The floor area beside the table and the volume under the tabletop are separate requirements.
For a numerical example, take a mock-up with a 900 mm top and measure each occupied chair as 550 mm from the corresponding long edge. The table and the two occupied bands take 2,000 mm. A project-specific decision to keep 1,100 mm clear on one side makes the cross-section 3,100 mm. Two such passages add up to 4,200 mm across the room. They are assumptions for the example. Passing, turning and the swing of nearby doors may call for more space, and the geometry at an integrated wheelchair place follows its own approach and under-table clearances. Measure again with a server stopping to place a dish. The person coming past needs space while the server is there.
The US 2010 ADA Standards are one example of how the requirements are divided. In covered projects, section 226.1 sets the minimum share of seating and standing spaces at dining surfaces that must comply with section 902 at five per cent. Section 226.2 calls for dispersion. Section 902 gives a top height of 28 to 34 inches (710 to 865 mm), with forward approach and the clear floor, knee and toe space referred to in sections 305 and 306. Section 305 defines a basic clear floor space of 30 by 48 inches (760 by 1,220 mm). Read these together with the route and relevant scoping provisions. Those figures apply within the US standards. They describe the conditions of an accessible dining position and leave the social and service arrangement around it open. US Access Board, ADA Standards, Chapter 2, section 226 US Access Board, ADA Standards, Sections 305 and 306 US Access Board, section 902, Dining Surfaces and Work Surfaces
The University at Buffalo's Wheeled Mobility Project measured occupied footprints and reach across people using manual chairs, powered chairs and scooters. Its findings show why the footrest, front of the device and the reachable part of the top are different points. A table detailed around walled-in supports can leave usable height at the front and still stop a person approaching far enough for their own plate. Keep supports or a low connecting rail clear of the approach and include actual mobility aids in the furniture trial. Center for Inclusive Design and Environmental Access, Anthropometry of Wheeled Mobility Project, 2010
Leave room to eat with the group
Where projects follow Approved Document M in England, use the guidance for buildings other than dwellings and read it with the project team against the work proposed. A roof, enclosure or door can have its own access implications, and furnishings and advance booking choices still need operational attention. The Design Council's inclusive design principles add a separate question about choice. A position with usable clearances at the far end of a long table might put diners who use it at a distance from their chosen companions. An accessible place along a side, with a removable chair and a base that leaves the approach clear, could give the same group a different choice. England, Approved Document M, Volume 2 Design Council, The Principles of Inclusive Design
Table dimensions must accommodate what is on the surface as well as the people below it. If the menu uses a wide platter, draw the gap between the near edge of the platter and the front of each diner. Ask whether the server can bring food to the side of the table that has the wheelchair position without reaching over another guest. A wide top can give people room to put things down and make reaching the contents more difficult. Consider smaller shared vessels or service from the edge of the table in that situation. Keep the circulation width and adjust the size of the dishes or the table setting first.
Diners using different mobility aids, including people who prefer to remain in their own chairs, can try the arrangement in a mock-up. Use the doors, service equipment and place settings that will be in the finished room. A useful drawing records the dimensions at the point of greatest conflict during service, with the position of the obstruction marked. The architect can then change the edge, the base, the chair or the route without losing track of which problem the alteration was meant to solve.