GOLEMArchitecture·Art·Design

06.e.4How can a restaurant design furniture for easy cleaning, maintenance and replacement?

A restaurant furniture specification should describe how staff will clean the pieces and replace worn parts. Identify which surfaces are wiped throughout service, which pieces have to move at closing and which parts are likely to fail first. Choose fasteners, finishes and covers with the people who will clean or replace them. Before ordering the full quantity, ask the supplier to show how one unit can be taken out of use and returned while the surrounding furniture stays in place.

What a test report covers

The British adoption BS EN 16139:2025 sets out safety, strength and durability tests for non-domestic seating within its published scope. BSI describes a scope for non-domestic seating intended for adults up to 110 kg and excludes properties including upholstery durability and flammability. Ask what furniture evidence covers the people and use beyond the published test scope. Treat the report as one part of the submission. Ask which seating assembly and options were tested and which applications the report covers. Ask the supplier whether a substituted pad or arm affects which configuration the report covers. For the cleaning brief, ask the fabric or finish supplier for the permitted products, procedures and contact times. Request the specification for the finish that will be installed. BSI, BS EN 16139:2025, Non-Domestic Seating Association for Contract Textiles, Performance Guidelines Association for Contract Textiles, Test Method for Chemical Compatibility

At a fixed bench, the cleaner needs to know how to reach the junction between a seat cushion and back. A narrow seam looks precise in a sample and can trap food below the top edge. An accessible gap or removable pad can work if the cleaner can reach it with the real tools provided. A wall-fixed bench can use a wipeable plinth or enough clearance for the cleaning head below it. If a tool must be held at an angle for the length of the bench, the recess will be hard to reach in a quick wipe. Try the proposed cleaner at the same time. Colour transfer, tackiness and damage at seams each call for a different adjustment. A fabric sample on a bench is only one part of the installed piece. Wiping the completed sample gives the seam, trim and substrate a part in the trial.

Arrange for the first small failure

At Café Boy in Zurich, supplier Girsberger describes restoring the existing wooden restaurant chairs during a renovation by OSMB Architekten Zürich and Natalina Di Iorio. Its report counts 85 chairs and describes repair, sanding, staining and new varnish. This is a case of keeping a complete batch of furniture in service through a larger refurbishment. It leaves the operator of a different restaurant the question of what they can repair at a smaller scale between those projects. Girsberger, Café Boy Remanufacturing Case Girsberger, Sustainability Report, Café Boy, p. 32

Emeco's product support lists replaceable glides for several seating families, with different options by model and floor surface. A specification can call for that level of detail. State which glide fits the legs, how it comes out and whether the operator can hold spares on site. The same applies to an upholstered pad. Agree who can remove it, where the fasteners are and how long it takes to obtain a replacement in an acceptable colour. A commercial finish can be renewed in part only if the owner knows what it is and which preparation the supplier permits. Emeco, Model-Specific Glides for the Navy Family

Use the maintenance plan to settle the design of the edge. A wrapped material that turns onto an inaccessible underside can be difficult to replace locally. A separate timber nosing may protect it but introduces another seam. Put a glass down against the joint during the prototype, let a little liquid reach the edge and watch where it goes. If the assembly needs to dry before a sealed pad is returned to use, check how the back and top are ventilated while it is off the floor. The detail belongs in the turnover procedure and in the tender price for replaceable parts.

The manufacturer can show how a part is replaced with the prototype against the proposed wall. Time how long a damaged seat would remain vacant if someone damaged it on a Friday evening. The operator has two service times to consider. Replacing a pad or glide from stock can happen between shifts. A chair that needs factory repair might be unavailable until a batch is collected, a service model documented for some furniture by Vitra. Put any minimum batch size and anticipated turn-around time beside the price. File the tools and part numbers where staff can find them, and keep the items needed for a single repair on site where the contract allows. Vitra, Refurbishment Services for Contract Furniture