GOLEMArchitecture·Art·Design

06.d.4Which materials can improve acoustic comfort in a restaurant or cocktail bar?

An absorptive ceiling or suspended panels can treat a restaurant or bar where enough overhead area is available. Add suitable absorbers to walls where their location addresses a particular reflection or part of the floor plan. Choose the thickness, backing and mounting together. Ask for performance by frequency and decide which surfaces have to resist spills, impacts or repeated washing. A product's colour or texture gives little information about how the installed assembly will behave.

A specification needs the complete assembly

ISO 354 describes measurement of absorption in a reverberation room. ISO 11654 describes a weighted single-number rating for building absorbers. In a specification, the two serve different purposes. The weighted rating helps compare certain products. Read the figures at individual frequencies alongside it, especially if the room has a pronounced low-frequency problem. An absorber sold in different thicknesses or with an optional air gap may have results for several constructions. Give each proposed construction the data for that installation. ISO 354:2003, Measurement of Sound Absorption in a Reverberation Room ISO 11654:1997, Sound Absorbers for Use in Buildings, Rating of Sound Absorption

A 2025 test report from ift Rosenheim for a Lindner product illustrates the distinction. The test used three circular absorbers 1,250 mm in diameter and 24 mm thick, at a total construction depth of 200 mm on wooden blocks. Its practical absorption coefficient was 0.25 at 125 Hz and 1.00 at 1,000 Hz, with a weighted rating of 0.95. The report flags the underlying absorption area at 125 Hz as too small. The figures describe absorption in that test configuration. How loud the occupied room will be depends on the sources, where the treatment goes and how much of it is installed. A room with a hard ceiling and a chatter problem has a different frequency and placement brief from a room transmitting low music frequencies into an adjoining tenancy. ift Rosenheim, Lindner Sound-Absorption Report H250129P1/1c_rev00, 2025

Where the material has to survive

Above a main dining area, absorption at the ceiling can leave low walls available for cleaning and impact resistance. A suspended panel can share the ceiling with lights, sprinklers and access to equipment if their locations are coordinated. At a wall, open fabric over a tested absorptive backing can contribute. Fabric over a solid board is a different construction. At a cooking or drinks area, request the allowed cleaning methods, moisture limits and edge details for the proposed product before putting it beside the pass. Ecophon's Hygiene Foodtec A documents acoustic results, maintenance conditions and fire classification for specific systems. Its specification shows 20 mm and 40 mm tiles at the same 200 mm total system depth and weighted rating of 0.90, with different results in individual bands. To coordinate the ceiling over a pass, keep the cleaning and edge details with the band figures while the services team sets the available depth. The depth belongs in the specification as well as on the ceiling drawing. England's Approved Document B is a separate reference for the building's fire design, which needs review for the complete lining in context. Ecophon, Hygiene Foodtec A, Product Specification England, Fire Safety, Approved Document B

At Ottolenghi Richmond, the acoustic installer describes a retrofit with suspended baffles and stretched fabric at the perimeter. This is an account of where the contractor treated the room. The installer’s account shows how the locations of broad ceiling treatment and perimeter treatment can coexist with the dining room's fittings. Resonics, Ottolenghi Richmond, Acoustic Fit-Out

Treat a panel near the floor differently from one suspended high. A low panel may need a facing that resists damage from chairs and carts and can be cleaned with the operator's approved products. A facing that closes its pores changes the acoustic assembly. At the ceiling, make sure the total treatment area survives the layout of the fittings. A proposal with a continuous absorber can arrive at the contractor as scattered pieces after the engineer and lighting designer add equipment. Assess the area and mounting of the final layout in the acoustic model. Hold one testable wall or ceiling detail through the reviews so the project team can compare what is being built with the proposed performance.

The contractor’s detail and the physical sample give the team something to compare before approving a substitute. If a panel must sit closer to the ceiling to fit a duct, ask what assembly the performance now corresponds to. Record how it can be removed when equipment above it needs servicing. These are matters for the material schedule and the setting-out drawing as well as the acoustic calculation.